If one day your car suddenly stops when you are driving on the road, what would you do? The reason is the battery dies; also there are the jumper cables with you, so do you think you can start your car again?
In this situation, there is a way that can help you use the jumper cables to jump a start to continue your trip. Follow these steps and do them carefully.
In this situation, there is a way that can help you use the jumper cables to jump a start to continue your trip. Follow these steps and do them carefully.
Step 1: Prepare the jumper cables
It is really great if you prepared for your own car a set of jumper cables available in your vehicle. However, if you do not, you can ask for help from the people who can assist you with their jumper cables.
Step 2: Park your car in the parking lot
You should park both your vehicle and the helping car in the parking lot and shut off the ignition. You should also brake both of them to make sure the safety. These two cars should be placed opposite or next to each other.
Step 3: Connect the positive terminals
To clarify clearly, the producers identify the positive terminal of the cables with red and the negative one with black.
First, you attach one of the red clips of the cable to the positive terminal (+) of your dead battery. Then, the other clip of this red cable will be attached to the positive terminal of the working car’s battery.
Step 4: Connect the negative terminals
In this step, you connect one of the black clips of the cable to the negative terminal (-) of the working battery. Besides, you should not attach the left clip of the cable to your dead battery’s negative terminal. Instead, you should connect it to an unpainted metal part of your car which is not near your battery. This makes sure that the jump will be safe.
Step 5: Start the working car
After finishing the connection, you start the working car and let its engine work for a few minutes. Thanks to this, your battery will be supplied with energy.
Step 6: Start your car
First, you should turn off the working car’s engine and then try to start your car. If it does not work, you should repeat the above step so that your battery can be supplied more. After that, you start your car again.
When your car is working, do not shut off but you can disconnect the jumper cables, which starts first with the black cable clips. If any part of the cables still connects to the car, you must remember not to let the clips touch each other.
Step 7: Drive your car around
After disconnecting the cables, you should take a short drive so that your battery can be recharged. However, if your car does not work the next time you start, you should check your battery and think about replacing it.
Using the jumper cables to start your car is an ideal solution in the case of your battery is dead. Therefore, you should always prepare for your own car a set of jumper cables for the bad situations.
It is really great if you prepared for your own car a set of jumper cables available in your vehicle. However, if you do not, you can ask for help from the people who can assist you with their jumper cables.
Step 2: Park your car in the parking lot
You should park both your vehicle and the helping car in the parking lot and shut off the ignition. You should also brake both of them to make sure the safety. These two cars should be placed opposite or next to each other.
Step 3: Connect the positive terminals
To clarify clearly, the producers identify the positive terminal of the cables with red and the negative one with black.
First, you attach one of the red clips of the cable to the positive terminal (+) of your dead battery. Then, the other clip of this red cable will be attached to the positive terminal of the working car’s battery.
Step 4: Connect the negative terminals
In this step, you connect one of the black clips of the cable to the negative terminal (-) of the working battery. Besides, you should not attach the left clip of the cable to your dead battery’s negative terminal. Instead, you should connect it to an unpainted metal part of your car which is not near your battery. This makes sure that the jump will be safe.
Step 5: Start the working car
After finishing the connection, you start the working car and let its engine work for a few minutes. Thanks to this, your battery will be supplied with energy.
Step 6: Start your car
First, you should turn off the working car’s engine and then try to start your car. If it does not work, you should repeat the above step so that your battery can be supplied more. After that, you start your car again.
When your car is working, do not shut off but you can disconnect the jumper cables, which starts first with the black cable clips. If any part of the cables still connects to the car, you must remember not to let the clips touch each other.
Step 7: Drive your car around
After disconnecting the cables, you should take a short drive so that your battery can be recharged. However, if your car does not work the next time you start, you should check your battery and think about replacing it.
Using the jumper cables to start your car is an ideal solution in the case of your battery is dead. Therefore, you should always prepare for your own car a set of jumper cables for the bad situations.
More detail you can go to here: http://mygaragestory.net/ to find more. Thank you!